| POWER SUPPLIES AND TRANSFORMERS |
|
Power Supplies : Model TE-1
The Power supplies are built in suitably sized steel cabinet employing modern technique and circuit, workable on 220 V 50 Hz. Meters for measuring voltage and current are built in protection with fuse or automatic.
Output HT = 0 to 300 Volts 30mA. LT. Variable to 1 to 6, 3 Amps with 2 meters for Volt/Current. Suitable for Diode Valve Experiment. |
Power Supply : Model TE-2
Main = 220V 50HGz. H.T. Output 0 to 300 Volts 30mA. L.T. 6.3 V 3 Amps.
Bias = 0 to 20V ±5mA with two meters for H.T. Volt and Current. |
Power Supplies : Model TE-3
Stabilized Power Supply Main 230 Volt 50 Hz. Out put H.T. 0 to 300V 50mA. L.T. - 6.3 Volt 3 Amps. Bias = 0 to 25V positive and negative, Stabilization + 1% with three meters for HT Volts. He current and bias Voltage suitable for Triode value experiment. |
Power Supplies : Model TE-4
Same as above, output, current 100mA. With three meters for continuous working suitable for electroforsis Apparatus. |
Power Supply : Model TE-5
Dual Power Supply for Pentode Valve Experiment, both stabiles ±1% workable on 220 Volt 50 Hz. With five meters.
HT1 = 0 to 300 Volts 50 mA
HT 2 = 0 to 300 Volts 25 mA
Bias = 0 to 25 volts 5 mA
L.T. = 6.3 Volt 3 Amps.
Suitable for pentode/tetrode valve experiments. |
Fixed Voltage I.C. Regulated Power Supplies
High quality, well filtered giving smooth fixed D.C. Voltage. Deal for running many training boards like operational amplifiers (Type-741), Integrated Circuit Timer (Type-555) and Integrated Circuit Regulator (Type-723).
(a) 5V or 6V at 500 mA
(b) 5V or 6V at 1A
(c) 9V or 12V at 500 mA
(d) 9V or 12V at 1A
(e) 15V or 18V at 500 mA
(f) 15V or 18V at 1A |
Fixed Voltage I.C. Regulated Dual Power Supplies
Two fixed voltages are provided in this unit.
(a) ±5V or ±6V at 500 mA
(b) ±5V or 6V at 1A
(c) ±9V or ±12V at 500 mA
(d) ±9V or 12V at 1A
(e) ±15V or ±18V at 500 mA
(f) ±15V or 18V at 1A |
Regulated Power Supply, Model TE-7
| Application : |
General purpose low cost laboratory power source ideally suited for analog and digital IC's |
| Output : |
Four fixed voltages, viz. +5V, -5V, +12V and -12V |
| Current : |
300mA max. for each |
| Regulation : |
±0.05% for no load to full load |
| Protection : |
Internally protected by over-current and thermal shutdown |
| Power Supply : |
220V ±10%, 50Hz |
|
Digital Regulated Power Supply. TE-8
| Output Voltage |
Output Current |
Meters |
| a) 0-15V |
1A |
2DPM(3½ digit) |
| (b) 0-15V |
2A |
2DPM(3½ digit) |
| (c) 0-15V |
3A |
2DPM(3½ digit) |
| (d) 0-15V |
5A |
2DPM(3½ digit) |
| (e) 0-15V |
10A |
2DPM(3½ digit) |
| (f) 0-30V |
1A |
2DPM(3½ digit) |
| (g) 0-30V |
2A |
2DPM(3½ digit) |
| (h) 0-30V |
3A |
2DPM(3½ digit) |
| (i) 0-30V |
5A |
2DPM(3½ digit) |
| (j) 0-30V |
10A |
2DPM(3½ digit) |
|
High Voltage Power Supply, Model EHT-11
Application : EHT source for photo multiplier tubes and other radiation detectors.
Polarity : +ve or -ve as required. Output : 0 to 1500V continuously variable Max. Current : 1 mA Load
Regulation : ±.5% for no load to full load Display : 3½ digit, 7 segment LED display with auto polarity
Power Supply : 220V ±10%, 50 Hz
Protection : Protected against overload and short circuit by current limiting technique. |
Power Supply Model TE-9
Most useful as stand by Dual Power Supply for Transistors and I.C. experiments workable on 220 Volts 50 Hz, can deliver output 0-30 Volts, at 1 Amps Positive and 0-30 Volts at 1 Amps. Negative, Stabilization ±0.1% with four meters. |
Power Supply Model TE-10
Transistorised, workable on 220 Volts 50 Hz. Variable: 0-30 Volts current 1 Amps, with 2 meters for Volts and current Stabilization ±5%. |
Power Supply Model TE-11
Dual Solid State Power Supply Variable from 0 to 15 Volts positive and 0-15 Volts negative at 500 mA continuously variable and + 5 Volts fixed supply at 400 mA for operational amplifiers and other I.C. experiments with two meters. Regulation ±0.1% with short circuit protection and overload current limiting, workable on 220 Volt 50 Hz. |
Power Supply Model TE-12
This supply is designed to meet requirement of general laboratory Continuously variable 0 to 30 V.D.C. at current 0 to 3 Amps, continuous. Load regulation ±.01% line regulation 0.1%. With two meters. Both Voltage and Current Variable. |
Battery Chargers
All battery chargers are compiled in steel cabinet workable on 220 V 50 Hz. protected with fuse. Meter for output current. Full wave bridge circuit is employed. Tested for continuous operation.
| Model
TE-15 |
6/12V
2 Amps. |
| Model
TE-16 |
18V 2
Amps : Automatic |
| Model
TE-17 |
6/12V
3 Amps. |
| Model
TE-18 |
6/12V
4 Amps. |
| Model
TE-19 |
6/12V
5 Amps. |
| Model
TE-20 |
6/12V
6 Amps. |
| Model
TE-21 |
18V 3
Amps : Automatic |
| Model
TE-22 |
18V 4
Amps : Automatic |
|
Battery Eliminators
Workable on 220V 50 Hz. Housed in steel cabinet. Socket or Band-Switch provided for Selection of Volts output, with ON/OFF switch and main indication.
| Model
TE-23 |
2 to 6
V 1 Amps. |
| Model
TE-24 |
2 to
12 V 2 Amps. |
| Model
TE-25 |
2 to
12 V 3 Amps. |
| Model
TE-26 |
2 to
12 V 4 Amps. |
| Model
TE-27 |
2 to
12V 5 Amps. |
| Model
TE-28 |
2 to
12V 6 Amps. |
Higher Voltage/current Battery Eliminators and Chargers can be manufactured on demand. |
Transformers & Stabilizers
Triode Transformers are wound with double enamelled copper wire and on cores of silicon alloy steel and vaccum impregnated. |
Manual
Variable Transformers
| Model TE-29 |
.2 VA |
| Model TE-30 |
.3 VA |
| Model TE-31 |
,5 VA |
| Model TE-32 |
1 KVA |
| Model TE-33 |
1.5 KVA |
| Model TE-34 |
2 KVA |
|
Automatic Transformers
| Model TE-35 |
.5 VA |
| Model TE-36 |
1 KVA |
| Model TE-37 |
1.5 KVA |
| Model TE-38 |
2.5 KVA |
| Model TE-39 |
Transformer for lamp and scale. |
| Model TE-40 |
Transformer for Microscope. |
| Model TE-41 |
Demonstration Transformer. |
| Model TE-42 |
Sodium lamp Transformer 35 Watt. |
| Model TE-43 |
Transformer High Voltage for gas discharge tube 3.5 KV. |
|
Dimmerstate/Variac/Auto Transformer
Variac These variable transformer deliver continuously variable A.C. voltage. The output is variable from 0-270 Volts from mains input of 240 volts. Contact between the winding and load is through a carbon brush which covers at least one turn of wire at all times. The areas of winding swept by the brush is plated with metal which eliminates oxidations and ensures a long working life with negligible maintenance.
Specifications :
Constructions : Enclosed in a metal box, has air cooling. The voltage is adjusted and indicated by a knob and dial on the top.
Termination : Mains input via main cable. Output via insulated 4mm socket terminals as well as 3-pin 5 amp. socket.
Indication : An ON/OFF and indicator is provided.
Overload Protection : Slow blow fuse in output line.
Output Volts
:
0-240 V (line voltage connection)
0-270 V (over voltage connection)
This sturdily constructed Auto Transformer, ideal for operating heating devices, A.C. Motors and others equipment reguiring adjusting input voltage.
This item is supplied with different current capacities as per requirement in hand. Output voltage 0-270V remains the same in each case. Rest specifications are as above.
a) Current Capacity : 2 Amp.
b) Current Capacity : 4 Amp.
c) Current Capacity : 6 amp.
d) Current Capacity : 8 Amp. |
